# Banana Pi R3 SD Card boot issue documentation debugging
## Setup
- flashed [fresh current OpenWrt](https://downloads.openwrt.org/releases/23.05.4/targets/mediatek/filogic/openwrt-23.05.4-mediatek-filogic-bananapi_bpi-r3-sdcard.img.gz) release image on sdcard
- Boot selection switches all up/1, selecting SD Card as boot medium
- USB-Serial connected
- No other devices inserted (no NVME, modem, USB device, etc.)
## Test Hardware
Tests were conducted with two different SD Card types. And from what I can tell two different batches of Bananapi R3 boards.
**Bananapi v1.1 batch 2347**
**Bananapi v1.1 batch 2311**
## Test Combinations
- Two diffentet sdcards
- 1. 2x Sandisk Ultra 32G (most probably genuine)
- 2. 1x Kioxia Exceria 32G
- Two different batches/lots of Bananapi R3
- 1. 2x v1.1 batch 2347
- 2. 3x v1.1 batch 2311
## Test Results
Some combinations fail to boot. Alghough they seem to be not fail completely deterministic.
| | batch 2347 | batch 2311 |
|-|-|-|
|Sandisk Ultra 32G| ❌ | ✅ |
|Kioxia Exceria 32G| ❌ | ✅ |
## Test logs
Complete boot logs of all four tested combinations.
### minicom_bpir3_v1.1_2347_kioxia32g_boot00.log ❌
```
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 103F 0000
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 300C 0028
F5: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [3000]
T0: 0000 0209 [010F]
Jump to BL
NOTICE: BL2: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL2: Built : 22:14:18, Jul 15 2024
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (2002MHz)
NOTICE: EMI: Using DDR4 settings
NOTICE: EMI: Detected DRAM size: 2048MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL31: Built : 22:14:18, Jul 15 2024
U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)
CPU: MediaTek MT7986
Model: BananaPi BPi-R3
DRAM: 2 GiB
Core: 53 devices, 24 uclasses, devicetree: embed
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: ff, ef, aa
MMC: mmc@11230000: 0
Loading Environment from MMC... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Loading Environment from MMC... *** Error - No Valid Environment Area found
*** Warning - bad env area, using default environment
Net: eth0: ethernet@15100000
** No partition table - mmc 0 **
Couldn't find partition mmc 0:4
Cannot read EFI system partition
** No partition table - mmc 0 **
Couldn't find partition mmc 0:4
Cannot read EFI system partition
Failed to persist EFI variables
Saving Environment to MMC... Writing to redundant MMC(0)... failed
Failed (1)
Saving Environment to MMC... Writing to redundant MMC(0)... failed
Failed (1)
Button 'reset' not found (err=-16)
( ( ( OpenWrt ) ) ) [SD card] U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)Press UP/DOWN to move, ENTER to select, ESC to quit1. Run default boot command.2. Boot system via TFTP.3. Boot production system from SD card.4. Boot recovery system from SD card.5. Load production system via TFTP then write to SD card.6. Load recovery system via TFTP then write to SD card.7. Install bootloader, recovery and production to NOR.8. Install bootloader, recovery and production to NAND.9. Reboot.a. Reset all settings to factory defaults.0. U-Boot consoleHit any key to stop autoboot: 3 Hit any key to stop autoboot: 2 Hit any key to stop autoboot: 1 spi-nand: spi_nand spi_nand@1: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: 00, ef, aa
'spi-nand0' is now active device
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
Using ethernet@15100000 device
TFTP from server 192.168.1.254; our IP address is 192.168.1.1
Filename 'openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb'.
Load address: 0x46000000
Loading: *
ARP Retry count exceeded; starting again
Wrong Image Format for bootm command
ERROR: can't get kernel image!
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
Using ethernet@15100000 device
TFTP from server 192.168.1.254; our IP address is 192.168.1.1
Filename 'openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb'.
Load address: 0x46000000
Loading: *
ARP Retry count exceeded; starting again
Wrong Image Format for bootm command
ERROR: can't get kernel image!
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
```
### minicom_bpir3_v1.1_2347_sdultra32g_boot00.log ❌
```
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 103F 0000
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 300C 0028
F5: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [3000]
T0: 0000 01FF [010F]
Jump to BL
NOTICE: BL2: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL2: Built : 22:14:18, Jul 15 2024
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (2002MHz)
NOTICE: EMI: Using DDR4 settings
NOTICE: EMI: Detected DRAM size: 2048MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL31: Built : 22:14:18, Jul 15 2024
U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)
CPU: MediaTek MT7986
Model: BananaPi BPi-R3
DRAM: 2 GiB
Core: 53 devices, 24 uclasses, devicetree: embed
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: ff, ef, aa
MMC: mmc@11230000: 0
Loading Environment from MMC... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Loading Environment from MMC... *** Error - No Valid Environment Area found
*** Warning - bad env area, using default environment
Net: eth0: ethernet@15100000
** No partition table - mmc 0 **
Couldn't find partition mmc 0:4
Cannot read EFI system partition
** No partition table - mmc 0 **
Couldn't find partition mmc 0:4
Cannot read EFI system partition
Failed to persist EFI variables
Saving Environment to MMC... Writing to redundant MMC(0)... failed
Failed (1)
Saving Environment to MMC... Writing to redundant MMC(0)... failed
Failed (1)
Button 'reset' not found (err=-16)
( ( ( OpenWrt ) ) ) [SD card] U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)Press UP/DOWN to move, ENTER to select, ESC to quit1. Run default boot command.2. Boot system via TFTP.3. Boot production system from SD card.4. Boot recovery system from SD card.5. Load production system via TFTP then write to SD card.6. Load recovery system via TFTP then write to SD card.7. Install bootloader, recovery and production to NOR.8. Install bootloader, recovery and production to NAND.9. Reboot.a. Reset all settings to factory defaults.0. U-Boot consoleHit any key to stop autoboot: 3 Hit any key to stop autoboot: 2 Hit any key to stop autoboot: 1 spi-nand: spi_nand spi_nand@1: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: 00, ef, aa
'spi-nand0' is now active device
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
Using ethernet@15100000 device
TFTP from server 192.168.1.254; our IP address is 192.168.1.1
Filename 'openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb'.
Load address: 0x46000000
Loading: *
ARP Retry count exceeded; starting again
Wrong Image Format for bootm command
ERROR: can't get kernel image!
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
Using ethernet@15100000 device
TFTP from server 192.168.1.254; our IP address is 192.168.1.1
Filename 'openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb'.
Load address: 0x46000000
Loading: *
ARP Retry count exceeded; starting again
Wrong Image Format for bootm command
ERROR: can't get kernel image!
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
Using ethernet@15100000 device
TFTP from server 192.168.1.254; our IP address is 192.168.1.1
Filename 'openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb'.
Load address: 0x46000000
Loading: *
```
### minicom_bpir3_v1.1_2311_sdultra32g_boot00.log ✅
```
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 103F 0000
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 300C 0028
F5: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [3000]
T0: 0000 01FF [010F]
Jump to BL
NOTICE: BL2: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL2: Built : 22:14:18, Jul 15 2024
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (2000MHz)
NOTICE: EMI: Using DDR4 settings
NOTICE: EMI: Detected DRAM size: 2048MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL31: Built : 22:14:18, Jul 15 2024
U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)
CPU: MediaTek MT7986
Model: BananaPi BPi-R3
DRAM: 2 GiB
Core: 53 devices, 24 uclasses, devicetree: embed
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: ff, ef, aa
MMC: mmc@11230000: 0
Loading Environment from MMC... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Loading Environment from MMC... OK
Net: eth0: ethernet@15100000
Cannot read EFI system partition
Cannot read EFI system partition
Failed to persist EFI variables
( ( ( OpenWrt ) ) ) [SD card] U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)Press UP/DOWN to move, ENTER to select, ESC to quit1. Run default boot command.2. Boot system via TFTP.3. Boot production system from SD card.4. Boot recovery system from SD card.5. Load production system via TFTP then write to SD card.6. Load recovery system via TFTP then write to SD card.7. Install bootloader, recovery and production to NOR.8. Install bootloader, recovery and production to NAND.9. Reboot.a. Reset all settings to factory defaults.0. U-Boot consoleHit any key to stop autoboot: 3 Hit any key to stop autoboot: 2 Hit any key to stop autoboot: 1 spi-nand: spi_nand spi_nand@1: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: 00, ef, aa
'spi-nand0' is now active device
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
MMC read: dev # 0, block # 131072, count 256 ... 256 blocks read: OK
MMC read: dev # 0, block # 131072, count 21192 ... 21192 blocks read: OK
## Loading kernel from FIT Image at 46000000 ...
Using 'config-mt7986a-bananapi-bpi-r3' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.162
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x46001000
Data Size: 5174998 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x44000000
Entry Point: 0x44000000
Hash algo: crc32
Hash value: f8127545
Hash algo: sha1
Hash value: fa6aa9c6fb98d027c64616a155bc90a6f84f3ca4
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-mt7986a-bananapi-bpi-r3' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464f1000
Data Size: 31591 Bytes = 30.9 KiB
Architecture: AArch64
Load Address: 0x43f00000
Hash algo: crc32
Hash value: 438ac94f
Hash algo: sha1
Hash value: b071387d5acc00d7b364d49838e59deffb964934
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from 0x464f1000 to 0x43f00000
## Loading fdt from FIT Image at 46000000 ...
Using 'mt7986a-bananapi-bpi-r3-sd' configuration
Trying 'fdt-mt7986a-bananapi-bpi-r3-sd' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-sd
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464fc000
Data Size: 327 Bytes = 327 Bytes
Architecture: AArch64
Hash algo: crc32
Hash value: 10a1281b
Hash algo: sha1
Hash value: 3bf645d15e8f58e0b7426c65bcf06464cc36d5c8
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'mt7986a-bananapi-bpi-r3-nand' configuration
Trying 'fdt-mt7986a-bananapi-bpi-r3-nand' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nand
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464fa000
Data Size: 915 Bytes = 915 Bytes
Architecture: AArch64
Hash algo: crc32
Hash value: 0c0a8e7d
Hash algo: sha1
Hash value: 3627abda155b1ffe23eef560e458c045aa49e7c5
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x43f00000
Working FDT set to 43f00000
## Loading loadables from FIT Image at 46000000 ...
Trying 'rootfs-1' loadables subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 rootfs
Type: Filesystem Image
Compression: uncompressed
Data Start: 0x464fd000
Data Size: 5619712 Bytes = 5.4 MiB
Hash algo: crc32
Hash value: a3b9bbe5
Hash algo: sha1
Hash value: 3fde5ffc0fbb57aff4ad163ee5701136143ad296
Verifying Hash Integrity ... crc32+ sha1+ OK
Uncompressing Kernel Image
Loading Device Tree to 00000000be7d3000, end 00000000be7dce0e ... OK
Working FDT set to be7d3000
Add 'ramoops@42ff0000' node failed: FDT_ERR_EXISTS
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.162 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Jul 15 22:14:18 2024
[ 0.000000] Machine model: Bananapi BPI-R3
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff]
[ 0.000000] node 0: [mem 0x000000004ffc0000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[ 0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/mmcblk0p65
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2041016K/2097152K available (8384K kernel code, 906K rwdata, 1488K rodata, 448K init, 300K bss, 56136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: 0xffffffc008010090
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000125] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000133] pid_max: default: 32768 minimum: 301
[ 0.000335] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.000348] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.001376] rcu: Hierarchical SRCU implementation.
[ 0.001662] smp: Bringing up secondary CPUs ...
[ 0.001909] Detected VIPT I-cache on CPU1
[ 0.001931] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.001958] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.002222] Detected VIPT I-cache on CPU2
[ 0.002233] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.002244] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.002476] Detected VIPT I-cache on CPU3
[ 0.002486] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.002495] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.002520] smp: Brought up 1 node, 4 CPUs
[ 0.002533] SMP: Total of 4 processors activated.
[ 0.002537] CPU features: detected: 32-bit EL0 Support
[ 0.002540] CPU features: detected: CRC32 instructions
[ 0.002561] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.002615] CPU: All CPU(s) started at EL2
[ 0.002625] alternatives: patching kernel code
[ 0.005524] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005545] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.005688] pinctrl core: initialized pinctrl subsystem
[ 0.006309] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.006553] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.006583] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.006608] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.006857] thermal_sys: Registered thermal governor 'fair_share'
[ 0.006860] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.006863] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006866] thermal_sys: Registered thermal governor 'user_space'
[ 0.007063] ASID allocator initialised with 65536 entries
[ 0.007375] pstore: Registered ramoops as persistent store backend
[ 0.007378] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.017193] cryptd: max_cpu_qlen set to 1000
[ 0.018752] 1.8vd: supplied by 12vd
[ 0.018913] 3.3vd: supplied by 12vd
[ 0.019169] SCSI subsystem initialized
[ 0.019256] libata version 3.00 loaded.
[ 0.020127] clocksource: Switched to clocksource arch_sys_counter
[ 0.020573] NET: Registered PF_INET protocol family
[ 0.020678] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.021343] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.021364] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.021372] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.021438] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[ 0.021606] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.021678] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021705] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021830] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.021849] PCI: CLS 0 bytes, default 64
[ 0.023772] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 0.026379] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.026391] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.048020] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.049107] pwm-mediatek 10048000.pwm: clock: top fail: -517
[ 0.049381] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 0.049401] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 0.049409] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 0.049490] /soc/pcie@11280000: Failed to get clk index: 0 ret: -517
[ 0.049499] mtk-pcie-gen3 11280000.pcie: failed to get clocks
[ 0.052390] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.054089] printk: console [ttyS0] disabled
[ 0.074243] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 122, base_baud = 2500000) is a ST16650V2
[ 0.762290] printk: console [ttyS0] enabled
[ 0.787092] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 123, base_baud = 1625000) is a ST16650V2
[ 0.816819] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 124, base_baud = 1625000) is a ST16650V2
[ 0.826642] mtk_rng 1020f000.rng: registered RNG driver
[ 0.826702] hwrng: no data available
[ 0.832118] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.843579] loop: module loaded
[ 0.846727] Loading iSCSI transport class v2.0-870.
[ 0.852799] spi spi0.0: setup: ignoring unsupported mode bits a00
[ 0.859129] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.864464] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.872713] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.879050] Creating 4 MTD partitions on "spi0.0":
[ 0.883864] 0x000000580000-0x000008000000 : "ubi"
[ 1.013796] 0x000000380000-0x000000580000 : "fip"
[ 1.020847] 0x000000080000-0x000000380000 : "reserved"
[ 1.029265] 0x000000000000-0x000000080000 : "bl2"
[ 1.163870] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009780000, irq 136
[ 1.173646] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009780000, irq 136
[ 1.183182] i2c_dev: i2c /dev entries driver
[ 1.188931] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.197462] NET: Registered PF_INET6 protocol family
[ 1.203085] Segment Routing with IPv6
[ 1.206757] In-situ OAM (IOAM) with IPv6
[ 1.210713] NET: Registered PF_PACKET protocol family
[ 1.215766] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.229066] 8021q: 802.1Q VLAN Support v1.8
[ 1.234218] pstore: Using crash dump compression: deflate
[ 1.245703] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 1.253027] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 1.259280] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 1.270374] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.280923] mmc0: new high speed SDHC card at address 5048
[ 1.287161] mmcblk0: mmc0:5048 SD32G 29.7 GiB
[ 1.295931] Alternate GPT is invalid, using primary GPT.
[ 1.302362] FIT: Selected configuration: "config-mt7986a-bananapi-bpi-r3" (OpenWrt bananapi_bpi-r3)
[ 1.311396] FIT: kernel sub-image 0x00001000..0x004f06d5 "kernel-1" (ARM64 OpenWrt Linux-5.15.162)
[ 1.321295] FIT: flat_dt sub-image 0x004f1000..0x004f8b66 "fdt-1" (ARM64 OpenWrt bananapi_bpi-r3 device tree blob)
[ 1.332494] FIT: flat_dt sub-image 0x004f9000..0x004f91dc "fdt-mt7986a-bananapi-bpi-r3-emmc" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-emmc)
[ 1.348811] FIT: flat_dt sub-image 0x004fa000..0x004fa392 "fdt-mt7986a-bananapi-bpi-r3-nand" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nand)
[ 1.365125] FIT: flat_dt sub-image 0x004fb000..0x004fb38f "fdt-mt7986a-bananapi-bpi-r3-nor" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nor)
[ 1.381265] FIT: flat_dt sub-image 0x004fc000..0x004fc146 "fdt-mt7986a-bananapi-bpi-r3-sd" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-sd)
[ 1.397228] FIT: filesystem sub-image 0x004fd000..0x00a58fff "rootfs-1" (ARM64 OpenWrt bananapi_bpi-r3 rootfs)
[ 1.407814] FIT: selecting configured loadable "rootfs-1" to be root filesystem
[ 1.415107] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p65(rootfs-1) p66(rootfs_data)
[ 1.480125] mtk-pcie-gen3 11280000.pcie: PCIe link down, ltssm reg val: 0x1000001
[ 1.487625] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[ 1.523045] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 1.532175] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.540861] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=144)
[ 1.561076] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=145)
[ 1.581128] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=146)
[ 1.601132] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=147)
[ 1.621143] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=148)
[ 1.632240] DSA: tree 0 setup
[ 1.637368] UBI: auto-attach mtd0
[ 1.640698] ubi0: default fastmap pool size: 45
[ 1.645212] ubi0: default fastmap WL pool size: 22
[ 1.649983] ubi0: attaching mtd0
[ 5.263200] ubi0: scanning is finished
[ 5.308265] ubi0: attached mtd0 (name "ubi", size 122 MiB)
[ 5.313752] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.320607] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.327374] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.334315] ubi0: good PEBs: 980, bad PEBs: 0, corrupted PEBs: 0
[ 5.340303] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 5.347503] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1642748947
[ 5.356613] ubi0: available PEBs: 465, total reserved PEBs: 515, PEBs reserved for bad PEB handling: 20
[ 5.365986] ubi0: background thread "ubi_bgt0d" started, PID 539
[ 5.372047] block ubiblock0_1: created from ubi0:1(rootfs)
[ 5.377703] clk: Disabling unused clocks
[ 5.392888] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 5.400170] Freeing unused kernel memory: 448K
[ 5.404631] Run /sbin/init as init process
[ 5.408709] with arguments:
[ 5.411665] /sbin/init
[ 5.414356] with environment:
[ 5.417479] HOME=/
[ 5.419824] TERM=linux
[ 5.544496] init: Console is alive
[ 5.547990] init: - watchdog -
[ 5.819625] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.842252] usbcore: registered new interface driver usbfs
[ 5.847757] usbcore: registered new interface driver hub
[ 5.853105] usbcore: registered new device driver usb
[ 5.861514] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[ 5.868900] xhci-mtk 11200000.usb: supply vusb33 not found, using dummy regulator
[ 5.877042] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.882269] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 5.892648] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 5.901814] xhci-mtk 11200000.usb: irq 128, io mem 0x11200000
[ 5.907626] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.912842] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 5.920225] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 5.927610] hub 1-0:1.0: USB hub found
[ 5.931374] hub 1-0:1.0: 2 ports detected
[ 5.935628] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.943983] hub 2-0:1.0: USB hub found
[ 5.947732] hub 2-0:1.0: 1 port detected
[ 5.953988] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.965740] init: - preinit -
[ 6.187966] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 6.196480] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 6.204632] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.212649] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.221687] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.390118] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 6.570767] hub 1-1:1.0: USB hub found
[ 6.574585] hub 1-1:1.0: 4 ports detected
[ 8.648792] F2FS-fs (mmcblk0p66): Mounted with checkpoint version = d70cad9
[ 8.657971] mount_root: switching to f2fs overlay
[ 8.665132] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.677017] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.713703] procd: - early -
[ 8.716633] procd: - watchdog -
[ 9.246376] procd: - watchdog -
[ 9.249729] procd: - ubus -
[ 9.271063] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.306626] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.313113] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.322676] procd: - init -
Please press Enter to activate this console.
[ 9.457257] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.468282] i2c-gpio i2c-gpio-0: using lines 427 (SDA) and 428 (SCL)
[ 9.474937] i2c-gpio i2c-gpio-1: using lines 429 (SDA) and 430 (SCL)
[ 9.484154] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[ 9.498119] Loading modules backported from Linux version v6.1.97-0-g7753af06eebfb
[ 9.505699] Backport generated by backports.git v6.1.97-1-0-g2431d56e
[ 9.515399] sfp sfp-1: Host maximum power 3.0W
[ 9.520734] sfp sfp-2: Host maximum power 3.0W
[ 9.602004] urngd: v1.0.2 started.
[ 9.709514] random: crng init done
[ 9.712916] random: 23 urandom warning(s) missed due to ratelimiting
[ 9.973555] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221012174743a
[ 9.973555]
[ 10.106817] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221012174805
[ 10.185873] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221012174937
[ 10.291174] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[ 10.299161] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[ 12.950947] PPP generic driver version 2.4.2
[ 12.955835] NET: Registered PF_PPPOX protocol family
[ 12.962925] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.507869] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 14.525014] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 14.533489] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 14.537702] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 14.549889] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.556493] br-lan: port 1(lan1) entered blocking state
[ 14.561876] br-lan: port 1(lan1) entered disabled state
[ 14.568681] device lan1 entered promiscuous mode
[ 14.573347] device eth0 entered promiscuous mode
[ 14.592312] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 14.602987] br-lan: port 2(lan2) entered blocking state
[ 14.608220] br-lan: port 2(lan2) entered disabled state
[ 14.615455] device lan2 entered promiscuous mode
[ 14.627898] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 14.637858] br-lan: port 3(lan3) entered blocking state
[ 14.643138] br-lan: port 3(lan3) entered disabled state
[ 14.650517] device lan3 entered promiscuous mode
[ 14.662825] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 14.672667] br-lan: port 4(lan4) entered blocking state
[ 14.677900] br-lan: port 4(lan4) entered disabled state
[ 14.685647] device lan4 entered promiscuous mode
[ 14.694530] mt7530-mdio mdio-bus:1f sfp2: configuring for inband/2500base-x link mode
[ 14.704282] br-lan: port 5(sfp2) entered blocking state
[ 14.709510] br-lan: port 5(sfp2) entered disabled state
[ 14.717058] device sfp2 entered promiscuous mode
[ 14.725513] mtk_soc_eth 15100000.ethernet eth1: configuring for inband/2500base-x link mode
[ 14.735560] br-wan: port 1(eth1) entered blocking state
[ 14.740840] br-wan: port 1(eth1) entered disabled state
[ 14.746289] device eth1 entered promiscuous mode
[ 14.756787] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 14.766595] br-wan: port 2(wan) entered blocking state
[ 14.771755] br-wan: port 2(wan) entered disabled state
[ 14.778256] device wan entered promiscuous mode
BusyBox v1.36.1 (2024-07-15 22:14:18 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.4, r24012-d8dd03c46f
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
```
### minicom_bpir3_v1.1_2311_kioxia32g_boot00.log ✅
```
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 103F 0000
F3: 1001 0000 [0200]
F3: 1001 0000
F6: 300C 0028
F5: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [3000]
T0: 0000 0209 [010F]
Jump to BL
NOTICE: BL2: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL2: Built : 22:14:18, Jul 15 2024
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (2002MHz)
NOTICE: EMI: Using DDR4 settings
NOTICE: EMI: Detected DRAM size: 2048MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7986-sdmmc-ddr4)
NOTICE: BL31: Built : 22:14:18, Jul 15 2024
U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)
CPU: MediaTek MT7986
Model: BananaPi BPi-R3
DRAM: 2 GiB
Core: 53 devices, 24 uclasses, devicetree: embed
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: ff, ef, aa
MMC: mmc@11230000: 0
Loading Environment from MMC... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Loading Environment from MMC... OK
Net: eth0: ethernet@15100000
Cannot read EFI system partition
Cannot read EFI system partition
Failed to persist EFI variables
( ( ( OpenWrt ) ) ) [SD card] U-Boot 2023.07.02-OpenWrt-r24012-d8dd03c46f (Jul 15 2024 - 22:14:18 +0000)Press UP/DOWN to move, ENTER to select, ESC to quit1. Run default boot command.2. Boot system via TFTP.3. Boot production system from SD card.4. Boot recovery system from SD card.5. Load production system via TFTP then write to SD card.6. Load recovery system via TFTP then write to SD card.7. Install bootloader, recovery and production to NOR.8. Install bootloader, recovery and production to NAND.9. Reboot.a. Reset all settings to factory defaults.0. U-Boot consoleHit any key to stop autoboot: 3 Hit any key to stop autoboot: 2 Hit any key to stop autoboot: 1 spi-nand: spi_nand spi_nand@1: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
jedec_spi_nor spi_nor@0: unrecognized JEDEC id bytes: 00, ef, aa
'spi-nand0' is now active device
* spi-nand0
- device: spi_nand@1
- parent: spi@1100a000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- page size: 0x800 bytes
- OOB size: 64 bytes
- OOB available: 24 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
- 0x000000000000-0x000000080000 : "bl2"
- 0x000000080000-0x000000380000 : "factory"
- 0x000000380000-0x000000580000 : "fip"
- 0x000000580000-0x000008000000 : "ubi"
MMC read: dev # 0, block # 131072, count 256 ... 256 blocks read: OK
MMC read: dev # 0, block # 131072, count 21192 ... 21192 blocks read: OK
## Loading kernel from FIT Image at 46000000 ...
Using 'config-mt7986a-bananapi-bpi-r3' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.162
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x46001000
Data Size: 5174998 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x44000000
Entry Point: 0x44000000
Hash algo: crc32
Hash value: f8127545
Hash algo: sha1
Hash value: fa6aa9c6fb98d027c64616a155bc90a6f84f3ca4
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-mt7986a-bananapi-bpi-r3' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464f1000
Data Size: 31591 Bytes = 30.9 KiB
Architecture: AArch64
Load Address: 0x43f00000
Hash algo: crc32
Hash value: 438ac94f
Hash algo: sha1
Hash value: b071387d5acc00d7b364d49838e59deffb964934
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from 0x464f1000 to 0x43f00000
## Loading fdt from FIT Image at 46000000 ...
Using 'mt7986a-bananapi-bpi-r3-sd' configuration
Trying 'fdt-mt7986a-bananapi-bpi-r3-sd' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-sd
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464fc000
Data Size: 327 Bytes = 327 Bytes
Architecture: AArch64
Hash algo: crc32
Hash value: 10a1281b
Hash algo: sha1
Hash value: 3bf645d15e8f58e0b7426c65bcf06464cc36d5c8
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'mt7986a-bananapi-bpi-r3-nand' configuration
Trying 'fdt-mt7986a-bananapi-bpi-r3-nand' fdt subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nand
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464fa000
Data Size: 915 Bytes = 915 Bytes
Architecture: AArch64
Hash algo: crc32
Hash value: 0c0a8e7d
Hash algo: sha1
Hash value: 3627abda155b1ffe23eef560e458c045aa49e7c5
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x43f00000
Working FDT set to 43f00000
## Loading loadables from FIT Image at 46000000 ...
Trying 'rootfs-1' loadables subimage
Description: ARM64 OpenWrt bananapi_bpi-r3 rootfs
Type: Filesystem Image
Compression: uncompressed
Data Start: 0x464fd000
Data Size: 5619712 Bytes = 5.4 MiB
Hash algo: crc32
Hash value: a3b9bbe5
Hash algo: sha1
Hash value: 3fde5ffc0fbb57aff4ad163ee5701136143ad296
Verifying Hash Integrity ... crc32+ sha1+ OK
Uncompressing Kernel Image
Loading Device Tree to 00000000be7d3000, end 00000000be7dce0e ... OK
Working FDT set to be7d3000
Add 'ramoops@42ff0000' node failed: FDT_ERR_EXISTS
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.162 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Jul 15 22:14:18 2024
[ 0.000000] Machine model: Bananapi BPI-R3
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff]
[ 0.000000] node 0: [mem 0x000000004ffc0000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[ 0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/mmcblk0p65
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2041016K/2097152K available (8384K kernel code, 906K rwdata, 1488K rodata, 448K init, 300K bss, 56136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: 0xffffffc008010090
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000001] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000125] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000132] pid_max: default: 32768 minimum: 301
[ 0.000339] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.000352] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.001375] rcu: Hierarchical SRCU implementation.
[ 0.001660] smp: Bringing up secondary CPUs ...
[ 0.001911] Detected VIPT I-cache on CPU1
[ 0.001932] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.001957] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.002220] Detected VIPT I-cache on CPU2
[ 0.002233] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.002244] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.002475] Detected VIPT I-cache on CPU3
[ 0.002485] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.002494] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.002520] smp: Brought up 1 node, 4 CPUs
[ 0.002533] SMP: Total of 4 processors activated.
[ 0.002537] CPU features: detected: 32-bit EL0 Support
[ 0.002540] CPU features: detected: CRC32 instructions
[ 0.002562] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.002614] CPU: All CPU(s) started at EL2
[ 0.002624] alternatives: patching kernel code
[ 0.005505] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005525] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.005671] pinctrl core: initialized pinctrl subsystem
[ 0.006292] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.006536] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.006566] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.006591] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.006839] thermal_sys: Registered thermal governor 'fair_share'
[ 0.006842] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.006845] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006848] thermal_sys: Registered thermal governor 'user_space'
[ 0.007048] ASID allocator initialised with 65536 entries
[ 0.007360] pstore: Registered ramoops as persistent store backend
[ 0.007364] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.017174] cryptd: max_cpu_qlen set to 1000
[ 0.018718] 1.8vd: supplied by 12vd
[ 0.018879] 3.3vd: supplied by 12vd
[ 0.019132] SCSI subsystem initialized
[ 0.019217] libata version 3.00 loaded.
[ 0.020091] clocksource: Switched to clocksource arch_sys_counter
[ 0.020538] NET: Registered PF_INET protocol family
[ 0.020643] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.021303] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.021323] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.021332] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.021398] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[ 0.021567] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.021640] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021667] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021790] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.021810] PCI: CLS 0 bytes, default 64
[ 0.023878] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 0.026506] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.026519] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.048777] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.049850] pwm-mediatek 10048000.pwm: clock: top fail: -517
[ 0.050140] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 0.050163] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 0.050173] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 0.050273] /soc/pcie@11280000: Failed to get clk index: 0 ret: -517
[ 0.050285] mtk-pcie-gen3 11280000.pcie: failed to get clocks
[ 0.053160] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.054837] printk: console [ttyS0] disabled
[ 0.074985] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 122, base_baud = 2500000) is a ST16650V2
[ 0.762590] printk: console [ttyS0] enabled
[ 0.787342] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 123, base_baud = 1625000) is a ST16650V2
[ 0.817057] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 124, base_baud = 1625000) is a ST16650V2
[ 0.826876] mtk_rng 1020f000.rng: registered RNG driver
[ 0.826935] hwrng: no data available
[ 0.832355] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.843819] loop: module loaded
[ 0.846967] Loading iSCSI transport class v2.0-870.
[ 0.853053] spi spi0.0: setup: ignoring unsupported mode bits a00
[ 0.859380] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.864685] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.872923] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.879259] Creating 4 MTD partitions on "spi0.0":
[ 0.884083] 0x000000580000-0x000008000000 : "ubi"
[ 1.015242] 0x000000380000-0x000000580000 : "fip"
[ 1.022318] 0x000000080000-0x000000380000 : "reserved"
[ 1.030862] 0x000000000000-0x000000080000 : "bl2"
[ 1.163827] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009780000, irq 136
[ 1.173635] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009780000, irq 136
[ 1.183180] i2c_dev: i2c /dev entries driver
[ 1.188949] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.197490] NET: Registered PF_INET6 protocol family
[ 1.203078] Segment Routing with IPv6
[ 1.206749] In-situ OAM (IOAM) with IPv6
[ 1.210723] NET: Registered PF_PACKET protocol family
[ 1.215775] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.228808] 8021q: 802.1Q VLAN Support v1.8
[ 1.233905] pstore: Using crash dump compression: deflate
[ 1.244895] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 1.252240] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 1.258492] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 1.273971] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.283874] mmc0: new high speed SDHC card at address 1234
[ 1.290119] mmcblk0: mmc0:1234 SA32G 29.1 GiB
[ 1.297769] Alternate GPT is invalid, using primary GPT.
[ 1.304110] FIT: Selected configuration: "config-mt7986a-bananapi-bpi-r3" (OpenWrt bananapi_bpi-r3)
[ 1.313146] FIT: kernel sub-image 0x00001000..0x004f06d5 "kernel-1" (ARM64 OpenWrt Linux-5.15.162)
[ 1.323045] FIT: flat_dt sub-image 0x004f1000..0x004f8b66 "fdt-1" (ARM64 OpenWrt bananapi_bpi-r3 device tree blob)
[ 1.334244] FIT: flat_dt sub-image 0x004f9000..0x004f91dc "fdt-mt7986a-bananapi-bpi-r3-emmc" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-emmc)
[ 1.350559] FIT: flat_dt sub-image 0x004fa000..0x004fa392 "fdt-mt7986a-bananapi-bpi-r3-nand" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nand)
[ 1.366877] FIT: flat_dt sub-image 0x004fb000..0x004fb38f "fdt-mt7986a-bananapi-bpi-r3-nor" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nor)
[ 1.383021] FIT: flat_dt sub-image 0x004fc000..0x004fc146 "fdt-mt7986a-bananapi-bpi-r3-sd" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-sd)
[ 1.398984] FIT: filesystem sub-image 0x004fd000..0x00a58fff "rootfs-1" (ARM64 OpenWrt bananapi_bpi-r3 rootfs)
[ 1.409570] FIT: selecting configured loadable "rootfs-1" to be root filesystem
[ 1.416863] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p65(rootfs-1) p66(rootfs_data)
[ 1.483027] mtk-pcie-gen3 11280000.pcie: PCIe link down, ltssm reg val: 0x1000001
[ 1.490530] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[ 1.525921] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 1.535054] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.543739] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=144)
[ 1.563956] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=145)
[ 1.583971] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=146)
[ 1.603973] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=147)
[ 1.623986] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=148)
[ 1.635135] DSA: tree 0 setup
[ 1.640266] UBI: auto-attach mtd0
[ 1.643578] ubi0: default fastmap pool size: 45
[ 1.648091] ubi0: default fastmap WL pool size: 22
[ 1.652883] ubi0: attaching mtd0
[ 5.265828] ubi0: scanning is finished
[ 5.310847] ubi0: attached mtd0 (name "ubi", size 122 MiB)
[ 5.316325] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.323192] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.329958] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.336901] ubi0: good PEBs: 980, bad PEBs: 0, corrupted PEBs: 0
[ 5.342890] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 5.350095] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1642748947
[ 5.359201] ubi0: available PEBs: 465, total reserved PEBs: 515, PEBs reserved for bad PEB handling: 20
[ 5.368574] ubi0: background thread "ubi_bgt0d" started, PID 543
[ 5.374661] block ubiblock0_1: created from ubi0:1(rootfs)
[ 5.380325] clk: Disabling unused clocks
[ 5.392437] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 5.399707] Freeing unused kernel memory: 448K
[ 5.404177] Run /sbin/init as init process
[ 5.408255] with arguments:
[ 5.411209] /sbin/init
[ 5.413901] with environment:
[ 5.417025] HOME=/
[ 5.419369] TERM=linux
[ 5.542663] init: Console is alive
[ 5.546150] init: - watchdog -
[ 5.817754] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.840204] usbcore: registered new interface driver usbfs
[ 5.845709] usbcore: registered new interface driver hub
[ 5.851048] usbcore: registered new device driver usb
[ 5.859410] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[ 5.866820] xhci-mtk 11200000.usb: supply vusb33 not found, using dummy regulator
[ 5.874951] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.880179] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 5.890632] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 5.899775] xhci-mtk 11200000.usb: irq 128, io mem 0x11200000
[ 5.905603] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.910821] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 5.918200] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 5.925589] hub 1-0:1.0: USB hub found
[ 5.929341] hub 1-0:1.0: 2 ports detected
[ 5.933595] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.941952] hub 2-0:1.0: USB hub found
[ 5.945708] hub 2-0:1.0: 1 port detected
[ 5.951992] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.963700] init: - preinit -
[ 6.185472] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 6.194039] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 6.202320] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.210239] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.219273] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.380074] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 6.560733] hub 1-1:1.0: USB hub found
[ 6.564547] hub 1-1:1.0: 4 ports detected
[ 8.639080] F2FS-fs (mmcblk0p66): Disable nat_bits due to incorrect cp_ver (3961952720552774360, 0)
[ 8.653043] F2FS-fs (mmcblk0p66): Mounted with checkpoint version = d70cad8
[ 8.661769] mount_root: switching to f2fs overlay
[ 8.669163] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.680765] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.716860] procd: - early -
[ 8.719782] procd: - watchdog -
[ 9.249484] procd: - watchdog -
[ 9.252847] procd: - ubus -
[ 9.271366] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.307104] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.313597] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.323211] procd: - init -
Please press Enter to activate this console.
[ 9.457457] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.468291] i2c-gpio i2c-gpio-0: using lines 427 (SDA) and 428 (SCL)
[ 9.475059] i2c-gpio i2c-gpio-1: using lines 429 (SDA) and 430 (SCL)
[ 9.484012] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[ 9.498001] Loading modules backported from Linux version v6.1.97-0-g7753af06eebfb
[ 9.505610] Backport generated by backports.git v6.1.97-1-0-g2431d56e
[ 9.515767] sfp sfp-1: Host maximum power 3.0W
[ 9.521060] sfp sfp-2: Host maximum power 3.0W
[ 9.602770] urngd: v1.0.2 started.
[ 9.706925] random: crng init done
[ 9.710325] random: 23 urandom warning(s) missed due to ratelimiting
[ 9.973512] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221012174743a
[ 9.973512]
[ 10.103601] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221012174805
[ 10.183558] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221012174937
[ 10.288910] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[ 10.296916] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[ 12.942784] PPP generic driver version 2.4.2
[ 12.947655] NET: Registered PF_PPPOX protocol family
[ 12.954828] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.521499] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 14.539611] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 14.548172] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 14.552424] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 14.564654] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.572238] br-lan: port 1(lan1) entered blocking state
[ 14.577471] br-lan: port 1(lan1) entered disabled state
[ 14.584159] device lan1 entered promiscuous mode
[ 14.588777] device eth0 entered promiscuous mode
[ 14.606013] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 14.615912] br-lan: port 2(lan2) entered blocking state
[ 14.621190] br-lan: port 2(lan2) entered disabled state
[ 14.628195] device lan2 entered promiscuous mode
[ 14.640328] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 14.650592] br-lan: port 3(lan3) entered blocking state
[ 14.655825] br-lan: port 3(lan3) entered disabled state
[ 14.662963] device lan3 entered promiscuous mode
[ 14.674824] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 14.684718] br-lan: port 4(lan4) entered blocking state
[ 14.689950] br-lan: port 4(lan4) entered disabled state
[ 14.697457] device lan4 entered promiscuous mode
[ 14.706185] mt7530-mdio mdio-bus:1f sfp2: configuring for inband/2500base-x link mode
[ 14.716002] br-lan: port 5(sfp2) entered blocking state
[ 14.721253] br-lan: port 5(sfp2) entered disabled state
[ 14.728653] device sfp2 entered promiscuous mode
[ 14.737270] mtk_soc_eth 15100000.ethernet eth1: configuring for inband/2500base-x link mode
[ 14.747311] br-wan: port 1(eth1) entered blocking state
[ 14.752582] br-wan: port 1(eth1) entered disabled state
[ 14.758005] device eth1 entered promiscuous mode
[ 14.768396] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 14.778176] br-wan: port 2(wan) entered blocking state
[ 14.783354] br-wan: port 2(wan) entered disabled state
[ 14.789849] device wan entered promiscuous mode
BusyBox v1.36.1 (2024-07-15 22:14:18 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.4, r24012-d8dd03c46f
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
```